Bihar SBTE Diploma Mechanical Paper on TOM & M

Bihar SBTE Diploma Mechanical 4th SEM May 2019 Paper on TOM & M

Sr. No. Questions with options
1 Piston,  piston rod and crosshead of a steam engine constitute ______link.

(a)  One

(b) Two

(c)  Three

(d) None of the above

2 Motion of circular rod in a circular hole is an example of ______ constrained motion

(a)  Successfully

(b) Completely

(c)  Partially

(d) Incompletely

3 Crankshaft rotating in the journal bearing of an engine forms a _____ pair

(a)  Screw

(b) Turning

(c)  Spherical

(d) Rolling

4 Tooth gearing is an example of ____ pair

(a)  Lower

(b) Higher

(c)  Sliding

(d) Spherical

5 The number of inversion for a slider crank mechanism is _____

(a)  6

(b) 5

(c)  4

(d) 3

6 At limiting condition, angle of repose is _____inclined angle

(a)  Greater than

(b) Less than

(c)  Equal to

(d) None of above

7 Centrifugal tension in belt _______ power transmission

(a)  Increases

(b) Decreases

(c)  Does not affect

(d) None of these

8 Module is the reciprocal of _______

(a)  Pressure angle

(b) Circular pitch

(c)  Dimetral pitch

(d) None of above

9 Selection of belt drive depends upon _____

(a)  Speed of shaft

(b) Power transmitted

(c)  Distance between two shafts

(d) All of the above

10 Due to slip in the belt velocity ratio of the belt drive ______

(a)  Increases

(b) Decreases

(c)  Does not change

(d) Any of the above

11 Centrifugal tension in belt acts on _____side of belt

(a)  Tight

(b) Stack

(c)  Both (a) & (b)

(d) None of these

12 When the sleeve of a Porter governor moves upwards, the governor speed _____

(a)  Increases

(b) Decreases

(c)  Remains unaffected

(d) Any of the above

13 For equilibrium of forces on ball of Porter governor _____force considered

(a)  Weight of ball

(b) Centrifugal force on ball

(c)  Tension in arm and link

(d) All of the above

14 When speed of engine fluctuates continuously above and below the mean speed, it is called _____ of governor.

(a)  Stability

(b) Hunting

(c)  Sensitivity

(d) None of these

15 The ratio of maximum fluctuation of speed to the mean speed is called _____ fluctuation of speed.

(a)  Maximum

(b) Minimum

(c)  Co-efficient of

(d) None of these

16 Fly wheel minimizes variation of speed in engine during ______

(a)  Every cycle

(b) Load change

(c)  Fuel supply

(d) None of these

17 Disc brake is an example of _____brake

(a)  Radial

(b) Axial

(c)  Both (a) & (b)

(d) None of these

18 The capacity of the brake depends upon ______

(a)  Unit pressure

(b) Co-efficient of friction

(c)  Peripheral velocity

(d) All of the above

19 The smallest circle that can be drawn to the cam profile is called ___ circle

(a)  Base

(b) Pitch

(c)  Cam

(d) None of these

20 The maximum travel of the follower from its lowest position to the topmost position is called _____

(a)  Pitch

(b) Trace point

(c)  Lift

(d) Pitch point

  Data Collected By – Rashmi
  Published On -20th May 2022
   
   

 

 


Posted

in

by

Tags:

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *