Bihar Polytechnic Mechanical 6th SEM Papers

Bihar SBTE Diploma Mechanical 6th SEM May 2019 Paper on Vehicle Maintenance

Sr. No. Questions with options
1 The valves have to be replaced if the metal to be remove for smoothening their end surface is more than

(a)  0.05 mm

(b) 0.5 mm

(c)  1.5 mm

(d)  5 mm

2 Maximum permissible ovality in a cylinder is usually

(a)  0.01 mm

(b) 0.1 mm

(c)  0.5 mm

(d) 1.00 mm

3 For checking the alignment of the crank shaft. The best method is to place it ______

(a)  On V-blocks

(b) On its ends

(c)  On lathe centres

(d) On a plane smooth table

4 The friction that occurs between the layers of oil in an oil firm is called

(a)  Viscous friction

(b) Solid friction

(c)  Boundary friction

(d) Greasy friction

5 Painting of automobile is done to

(a)  Prevent rust from growing on the body

(b) Improve its external appearance

(c)  Retain the characteristics of steel for long

(d) All of the above

6 The brake warning light warns the driver of

(a)  Water in the master cylinder

(b) Air in the hydraulic system

(c)  Failure of the primary or the secondary circuit of hydraulic system

(d) Power brake failure

7 The condition that results in large quantities of H.C emission is

(a)  High temperature combustion

(b) Incomplete combustion

(c)  Low temperature combustion

(d) High atmospheric temperature combustion

8 When the battery is half (50%) charged, the electrolyte of specific gravity of a battery is usually

(a)  0.74

(b) 1.00

(c)  1.12

(d) 1.19

9 The engine oil level should be checked

(a)  Immediately after the ignition switch is turned off

(b) While the engine is running

(c)  A few minutes after the ignition switch is turned off

(d) While the engine is running at high idle speed

10 If the spark plug deposit indicates black coating of soot, it indicates that the engine has been generally operating on

(a)  Tool in mixture e

(b) Stoichiometric mixture

(c)  Most economical mixture

(d) Too rich mixture

   

 

11 The reconditioning process used to give cylinder bore surface across hatch pattern is known as

(a)  Honing

(b) Porous plating

(c)  Boring

(d) Shot peening

12 Vulcanizing means

(a)  Heating rubber under pressure

(b) Spraying with special paint

(c)  Melting rubber while stirring it

(d) None of the above

13 The condition that causes vapour locking in a brake system is

(a)  Over heating of the fluid due to frequent brake application

(b) Over cooling of the brake during high speed driving

(c)  Keeping the vehicle without use for an extended period

(d) An excessively high engine speed on down hill road

14 The adjustment for backlash in a differential is provided between

(a)  Crown wheel and the sun gear

(b) Sun gear and the plant gear

(c)  Crown wheel and the drive pinion

(d) Crown wheel and the planet geat

15 The purpose of tyre rotation on automobile is to

(a)  Avoid ply separation

(b) Equalize wear

(c)  Get better ride

(d) None of the above

16 The maximum disc run out allowed on the vehicle is generally

(a)  1 mm

(b) 0.5 mm

(c)  0.1 mm

(d) 0.01 mm

17 In modern vehicles, the headlight dimming switch is mounted on the

(a)  Steering column

(b) Dash board

(c)  Floor board

(d) Side pannel

18 When the choke is applied the fuel comes out from the

(a)  Main jet

(b) Idle port

(c)  Transfer port

(d) Progression hole

19 The clutch slippage while clutch is engaged is particularly noticeable

(a)  During idling

(b) During acceleration

(c)  During braking

(d) None of the above

20 The probable cause for un even wear of tyres for heavy vehicles could be

(a)  Excessive camber

(b) Incorrect castor

(c)  Over loading on vehicle

(d) All of the above

  Data Collected By – Rashmi
  Published On – 15th May 2022
   
   

Posted

in

by

Tags:

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *